Footwear Testing Equipment

Product Details:

We are the leading manufacture &Supplier of different type of qualityTesting & measuring Instruments 


As per IS 15298

Additional Information:

• Delivery Time: 20 Days

Product Details:

We are the leading manufacture &supplier of different type of qualityTesting & Measuring instruments AS PER IS 15298

Additional Information:

• Delivery Time: 20 DAYS

Product Details:

Outsoles of footwear or other flexing components may suffer cracking in use due to flexing. Cracks usually develop at points of high surface strain resulting from the design of the sole pattern, without there being any cuts to initiates them. The Belt Flex Tester is designed to flex complete sales with their patterns intact in a manner similar to those encountered in actual use. Tests carried out using it provide a guide to the risk of such cracks developing during use. The test specimens are attached to the outside of a continuous belt, which is driven around two rollers. The large roller drives the belt while movement of the smaller roller is chosen to make the flexing somewhat more severe than is actual use. This form of flexing also closely simulates the actual bending at each step as it produces a short period of rapid flexing followed by a longer period when the specimen is not being flexed. A normal test consist of a number of flexing runs up to a total of 50,000 flexes, with an examination for cracking at the end of each run.The Belt Flex Tester consists of two roller on which a flat belt moves. The larger roller which is the driving roller rotates at a specified speed to give the specified frequency of flexing with the help of an electric motor and V-belt arrangement. The second roller, which is the flexing roller, rotates with the movement of the belt.The flexing rollers are slightly barrel-shaped so as to minimize sideways movement of the belt. A hand wheel is attached to the front end of these rollers to enable the belt to be moved by hand. The equipment is supplied with three flexing rollers, one for normal sales, the second for very flexible soles, and the third for very rigid soles.

The distance between the driving and the flexing rollers can adjust with the help of a screw arrangement to enable the belt to be mounted over different flexing rollers and to allow for small differences in belt length. This is done by turning a hand wheel on the side of the tester.The tester is fitted with an acrylic front cover and a wire mesh safety guard, which allows adequate circulation of cooling air around the test specimens during the test. For the safety of the user, the motor can be started only when the cover is closed.

Additional Information:

• Delivery Time: 30 days

Product Details:

 

            The ability of light leathers such as those used in shoe uppers, gloves and garments to with stand repeated flexing without cracking is determined with the help of a flexometer. In this test, the test specimens in the shape of rectangular pieces are folded and clamped at each end to maintain them in a folded position in a set of grips, one of which is fixed while the other is able to oscillate. The movement of the oscillating grip causes the fold in the test specimen to run along its fold. This operation is carried out repeatedly and the test specimens inspected periodically to Asses the damaged produced.

As per IS 15298

Additional Information:

• Delivery Time: 30 days

Product Details:

We are the leading manufacture &Supplier of different type of qualityTesting & measuring Instruments 

as per SATRA PM92, IS:8085 part 2

Additional Information:

• Production Capacity: 20 units per month
• Delivery Time: 20Days

Product Details:

We are the leading manufacture &Supplier of different type of qualityTesting & measuring Instruments 
AS PER IS 15298

Additional Information:

• Delivery Time: 20 Days

Product Details:

We are the leading manufacture &Supplier of different type of qualityTesting & measuring Instruments 
As per IS 15298

Additional Information:

• Delivery Time: 20 DAYS

Product Details:

We are the leading manufacture &Supplier of different type of qualityTesting & measuring Instruments 

As per IS 15844

Additional Information:

• Delivery Time: 20 Days

Product Details:

We are the leading manufacture &Supplier of different type of qualityTesting & measuring Instruments 



As Per ISO 4643

Additional Information:

• Delivery Time: 20 days

Product Details:

We are the leading manufacture &Supplier of different type of qualityTesting & measuring Instruments 

we aree the manufacturer of Hawai chappal Test Equipments as per IS:10702,

Additional Information:

• Item Code: IS10702
• Production Capacity: 30 set per month
• Delivery Time: 20 Days
• Packaging Details: Standard Accessories

Product Details:

Used for testing flexing properties of flexible conduits

Product Details:

ASIAN direct reading Specific Digital Gravity Balance provides a simple and quick mean to read directly the specific gravity of rubber and other elastomers. Thus reducing labor and eliminating calculations. The time taken to find out specific gravity of a sample is only about half a minute. The balance consists of a rigid scale with a specific gravity (SG) printed on standing vertically on a heavy base plate. To the center point at the scale, through jewel bearings to minimize the friction, a balancing arm is pivoted. At one end of the arm, two stainless steel pins are hanging with yarns. One of the pins is attached to glass jar kept on the base. A guard is provided to avoid accidental falling of the jar during use. At the other and of the balancing arm a pointer is fixed which indicates the specific gravity of materials under test. A sliding weight is also provided for initial balancing of the sample of different weight a leveling of the base plate. Two models of balance, one with a range of specific gravity between 0.9 to 3.0'''' the second with a range of specific gravity / between 0.2to2.0 are available. A sample of any shape weighing between 5 and 12g can be tested in the first model, that weighing between 3 and 5g can be tested in the second model, and that weighing between 1and 2g can be tested in the third made. In the case of the second and third model, the lower pin is quite heavy and also acts as a sinker. Also in these models, the glass jar is kept on the base of a frame, which can be slid up and down on a rod fixed to the base plate to cover the full range at specific gravity.

Product Details:

As per IS 8085 part-1

Additional Information:

• Delivery Time: 12 Days

Product Details:

ASIAN direct reading Specific Gravity Balance provides a simple and quick mean to read directly the specific gravity of rubber and other elastomers. Thus reducing labor and eliminating calculations. The time taken to find out specific gravity of a sample is only about half a minute. The balance consists of a rigid scale with a specific gravity (SG) printed on standing vertically on a heavy base plate. To the center point at the scale, through jewel bearings to minimize the friction, a balancing arm is pivoted. At one end of the arm, two stainless steel pins are hanging with yarns. One of the pins is attached to glass jar kept on the base. A guard is provided to avoid accidental falling of the jar during use. At the other and of the balancing arm a pointer is fixed which indicates the specific gravity of materials under test. A sliding weight is also provided for initial balancing of the sample of different weight a leveling of the base plate. Two models of balance, one with the range of specific gravity between 0.9 to 3.0’’ the second with the range of specific gravity / between 0.2to2.0 are available. A sample of any shape weighing between 5 and 12g can be tested in the first model, that weigh between 3 and 5g can be tested in the second model, and that weighing between 1and 2g can be tested in the third made. In the case of the second and third model, the lower pin is quite heavy and also acts as a sinker. Also in these models, the glass jar is kept on the base of a frame, which can be slid up and down on a rod fixed to the base plate to cover the full range at specific gravity.

Specifications:

In the case of the model with range 0.9 to 3.0 SG scale is calibrated as under:

• From 0.9 to 2.0: graduated in division of 0.01
• From 2.0 to 2.5: graduated in division of 0.02
• From 2.5 to 3.0: graduated in division of 0.05

In the case of a model with range 0.2 to 2.0 SG scale is calibrated as under:

• From 0.3 to 0.8: graduated in division of 0.005
• From 0.8 to 1.5: graduated in division of 0.01
• From 1.5 to 2.0: graduated in division of 0.02

In the case of a model with range 0.05 to 0.7 SG scale is calibrated as under:

• From 0.05 to 0.1: graduated in division of 0.001
• From 0.1 to 0.2: graduated in division of 0.002
• From 0.2 to 0.4: graduated in division of 0.005
• From 0.4 to 0.5: graduated in the division of 0.01.
• From 0.5 to 0.7: graduated in the division of 0.02.

Product Details:

ASIAN Sole Adhesion Tester is used for the sole adhesion of the footwear.  The system consists of a spring dynamometer to indicate the load applied at the junction of the sole and the upper, a lever arrangement to transmit the load exerted on the toe piece to the spring dynamometer, a straight edge fulcrum for resting the shoe on during the test, and a set of interchangeable toe pieces having different curvature. The spring dynamometer indicates the load applied on the joint directly in kilograms, taking into account the mechanical advantage of the lever transmitting the force from the toe piece to it. The load is indicated on a circular dial. The dynamometer has two pointers, a black powder to indicate the instantaneous load acting on the toe piece and a red dummy pointer to indicate the maximum load applied before failure of adhesion. The toe piece is five in number and having a different curvature to enable toes and heels of different shapes and sizes to be tested. The length of the arc of each toe piece, however, is the same to ensure that the load is applied only to a fixed length of joint. They are made from carbon steel for giving a long operational life. Any one of the toe pieces can be held in the equipment at one time. The fulcrum on which the shoe is placed during the test has an adjustable height to enable soles of different thickness to be tested. The height of the fulcrum is adjusted with the help of spacer strips provided with the instrument. The instrument is finished in painting and bright chrome plating to give it a corrosion resistant finish.

Other Details:

• IS 8085(part I) - 1986: Method of test for footwear Part I: Dimensions, fitting, adhesion test, peel test, heat resistance test, and aging test.
• IS 11226 - 1993: Specification for leather safety footwear having direct molded sole.

Additional Information:

• Item Code: SoleAdAna
• Production Capacity: 50 Pieces per month
• Delivery Time: 10 Days
• Packaging Details: Basic instrument 5 Pieces curvature toe pieces Alen Key Operating Manual Calibration Certificate

Product Details:

We are the leading manufacture &Supplier of different type of qualityTesting & measuring Instruments 


As Per IS 8085 part-1

Additional Information:

• Delivery Time: 12 Days

Product Details:

We are the leading manufacture &Supplier of different type of qualityTesting & measuring Instruments 


used for testing of safety footwear

Additional Information:

• Delivery Time: 20 days

Product Details:

ASIAN Sole Adhesion Tester is used for the sole adhesion of the footwear. Digital model is also available. The system consists of a spring dynamometer to indicate the load applied at the junction of the sole and the upper, a lever arrangement to transmit the load exerted on the toe piece to the spring dynamometer, a straight edge fulcrum for resting the shoe on during the test, and a set of interchangeable toe pieces having different curvature. The spring dynamometer indicates the load applied on the joint directly in kilograms, taking into account the mechanical advantage of the lever transmitting the force from the toe piece to it. The load is indicated on a circular dial. The dynamometer has two pointers, a black powder to indicate the instantaneous load acting on the toe piece and a red dummy pointer to indicate the maximum load applied before failure of adhesion. The toe piece is five in number and having a different curvature to enable toes and heels of different shapes and sizes to be tested. The length of the arc of each toe piece, however, is the same to ensure that the load is applied only to a fixed length of joint. They are made from carbon steel for giving a long operational life. Any one of the toe pieces can be held in the equipment at one time. The fulcrum on which the shoe is placed during the test has an adjustable height to enable soles of different thickness to be tested. The height of the fulcrum is adjusted with the help of spacer strips provided with the instrument. The instrument is finished in painting and bright chrome plating to give it a corrosion resistant finish.


Other Details:

• IS 8085(part I) - 1986: Method of test for footwear Part I: Dimensions, fitting, adhesion test, peel test, heat resistance test, and aging test.
• IS 11226 - 1993: Specification for leather safety footwear having direct molded sole.

Product Details:

We are the leading manufacture &Supplier of different type of qualityTesting & measuring Instruments 

AS PER IS 13217-1991

Additional Information:

• Delivery Time: 20 DAYS

Product Details:

We are the leading manufacture &Supplier of different type of qualityTesting & measuring Instruments 


As Per JASO 313

Additional Information:

• Delivery Time: 12 DAYS

Product Details:

We are the leading manufacture &Supplier of different type of qualityTesting & measuring Instruments 

Easy and effecient equipment

Product Details:

We are the leading manufacture &Supplier of different type of qualityTesting & measuring Instruments 


Used for Safety footwear

Product Details:

We are the leading manufacture &supplier of different type of qualityTesting & Measuring instruments Measure angle Vs Load on the sample

Additional Information:

• Delivery Time: 20 days

Product Details:

We are the leading manufacture &Supplier of different type of qualityTesting & measuring Instruments 


As Per IS15298

Additional Information:

• Item Code: 9024
• Delivery Time: 10 Days
• Packaging Details: Wooden Packing

Product Details:

Bennewart Flex Tester is intended to determine the resistance of a component of material to cut growth during repeated flexing. It can also be used to assess the effect of surface patterns on crack initiation and growth. This test is especially applicable to the outsoles of footwear, but may also be used with certain other flexible components.The Bennewart Flex Tester consists of a drive unit comprising an electric motor with pulleys and belts and link mechanism to give an oscillating movement to one of the two grips holding the two ends of the test specimen, the other grip being fixed.The oscillating grip has gun metal bushes, which slides on two hardened and ground bearing steel rods to give it a long working life. Each grip consists of swayable bases pivoted on ball bearings so that the two ends of the test specimen are free to align themselves with the natural contour of the specimen during flexing. The axis about which the grip bases oscillate life. A six digit pre-set electronic digital counter the numbers of test cycles and also stops the motor after pre-set numbers of test cycles. The apparatus is finished in gray hammer tone shaving, painting, and bright chrome/ zinc plating to give it a corrosion resistant finish. A cutting dies for the preparation of test specimen from the sheet and sitting punch with a jig for making initial crack are available as optional accessories.

Additional Information:

• Delivery Time: 20 days

Product Details:

We are the leading manufacture &Supplier of different type of qualityTesting & measuring Instruments 


used for safety footwear

Product Details:

We are the leading manufacture &Supplier of different type of qualityTesting & measuring Instruments 
as per related standards

Product Details:

We are the leading manufacture &Supplier of different type of qualityTesting & measuring Instruments 



A.s Per IS 15298

Additional Information:

• Delivery Time: 20 Days